Datos Técnicos
Recubrimientos en polvo de curado UV sobre metal
| Application Data | ||
|---|---|---|
| Application | Powder is typically sprayed using corona electrostatic spray guns. | |
| Melt | Melt times will range from 1-4 minutes depending on metal thickness, part size, oven set temperatures and type of oven. | |
| UV Cure | Opaque powder coatings should be cured using gallium-doped lamps using the correct dosage and intensity range. UVA dosage of 400-1200 mJ/cm2 and intensity of 150-700 mW/cm2 UVB dosage of 300-700 mJ/cm2 and intensity of 100-500 mW/cm2 UVC dosage of 60-150 mJ/cm2 and intensity of 20-100 mW/cm2 A coating temperature of 100-130°C (212-266ᵒF) is recommended at the time of cure. | |
| UV LED Cure | Unpigmented and pigmented powder coatings will cure using a UV LED lamp under the correct parameters. Contact Keyland Polymer for product and process information. | |
| Storage and Shelf Life | Dry and cool conditions below 18°C (65°F) for 6 months are recommended for storage stability. Contact Keyland Polymer to confirm the appropriate storage conditions for your product. | |
| Technical Properties | ||||
| Gloss | ASTM D 523 | 3-95 GU @60° | ||
| Adhesion | ASTM D 3359, Method B | 4B Minimum | ||
| Pencil Hardness | ASTM D 3363 | H – 4H | ||
| Impact Resistance | ASTM D 2794 | 15-160+ in. -lbs Direct 15-160+ in. -lbs Indirect | ||
| Abrasion Resistance | ASTM D 4060 CS-17 Wheel, 500g, 500 cycles | 10 – 35 mg material loss | ||
| Conical Mandrel | ASTM D 552 | 1/8″ Mandrel No Cracking | ||
| Salt Spray | ASTM B 117 | 1000 Hours Pass <1/8″ Scribe Creep No Blisters | ||
Las propiedades de la película se determinaron utilizando una película en polvo de 1.7-2.3 mils (43-58 μm) sobre hierro pretratado fosfatado, enjuagado al cromo, calibre 22, paneles de prueba de acero laminado en frío sin pulir. El impacto se determinó en 2.0 mils.
Revisión 1 de marzo de 2023
Recubrimientos en polvo de curado UV sobre plásticos y compuestos
| Application Data | ||
|---|---|---|
| Application | Powder is typically sprayed using corona electrostatic spray guns. Most plastic materials and some carbon fiber materials require use of a conductive aid to allow for electrostatic transfer. Contact Keyland Polymer for more information. | |
| Melt | Melt times will range from 0.5-3 minutes depending on polymer base, part size/ dimensions, oven set temperatures, and type of oven. | |
| UV Cure | Opaque powder coatings should be cured using gallium-doped lamps using the correct dosage and intensity range. UVA dosage of 400-1200 mJ/cm2 and intensity of 150-700 mW/cm2 UVB dosage of 300-700 mJ/cm2 and intensity of 100-500 mW/cm2 UVC dosage of 60-150 mJ/cm2 and intensity of 20-100 mW/cm2 A coating temperature of 100-130°C (212-266ᵒF) is recommended at the time of cure. | |
| UV LED Cure | Unpigmented and pigmented powder coatings will cure using a UV LED lamp under the correct parameters. Contact Keyland Polymer for product and process information. | |
| Storage and Shelf Life | Dry and cool conditions below 18°C (65ᵒF) for 6 months are recommended for storage stability. Contact Keyland Polymer to confirm the appropriate storage conditions for your product. | |
| Technical Properties | ||||
| Gloss | ASTM D 523 | 3-90 GU @60° | ||
| Adhesion | ASTM D 3359, Method B | 4B Minimum | ||
| Pencil Hardness | ASTM D 3363 | H – 4H | ||
| Abrasion Resistance | ASTM D 4060 CS-17 wheel, 500 g, 1000 cycles | 10 – 35 mg material loss | ||
Las propiedades de la película se determinaron promediando los resultados de las pruebas de una variedad de sustratos de polímeros y fibra de carbono comunes con un espesor de película de polvo de 1,8-2,5 mils (46-64 µm).
Revisión 1 de marzo de 2023
Pintura en polvo de curado UV sobre madera
| Application Data | ||
|---|---|---|
| Application | Powder is typically sprayed using corona electrostatic spray guns. Preheating of MDF should be kept to a minimum to reach recommended surface temperature of 60-70°C (140-158°F), typically 1-2 minutes. | |
| Melt | Melt times will range from 1-3 minutes depending on MDF thickness, part size, oven set temperatures and type of oven. | |
| UV Cure | Opaque powder coatings should be cured using gallium-doped lamps using the correct dosage and intensity range. UVA dosage of 400-1200 mJ/cm2 and intensity of 150-700 mW/cm2 UVB dosage of 300-700 mJ/cm2 and intensity of 100-500 mW/cm2 UVC dosage of 60-150 mJ/cm2 and intensity of 20-100 mW/cm2 A coating temperature of 100-130°C (212-266ᵒF) is recommended at the time of cure. | |
| UV LED Cure | Unpigmented and pigmented powder coatings will cure using a UV LED lamp under the correct parameters. Contact Keyland Polymer for product and process information. | |
| Storage and Shelf Life | Dry and cool conditions below 18°C (65°F) for 6 months are recommended for storage stability. Contact Keyland Polymer to confirm the appropriate storage conditions for your product. | |
| Technical Properties | ||||
| 60° Gloss | ASTM D 523 | 3 – 90 | ||
| Film Build | ASTM D 4138, Method A Destructive, Tooke Gauge | 3 – 5 mils | ||
| Adhesion | ASTM D 3359, Method A- (X-Scribe | 4A Minimum | ||
| Pencil Hardness | ASTM D 3363 | H – 4H | ||
| Impact | NEMA LD 3-2005, Test Method 3.8 | 35-60+ in. minimum, no cracking | ||
| Abrasion Resistance | ASTM D 4060, CS-17 Wheel, 500g, 1000 cycles | 10 – 35 mg material loss | ||
| Boiling Water Resistance | NEMA LD 3-2005, Test Method 3.5 | No blistering | ||
Revisión 1 de marzo de 2023
